V11 function description

1.Vehicle powerable 

1.1Software Featuresable

1.1.1switchmachine

ShutdownIn state, long press the power button1seconds to start up;Long press the power button1Seconds to shut down.

1.1.2Stimulatelive

FactoryWhen the vehicle is inactive, the vehicle will prompt you to activate it, and the speed limit is5km/h.

1.1.3Front lightinglamp

Boot statusIn this state, short press the power button to turn the front light on and off.APPSwitch the front lights.

1.1.4 DRL(OKHeadlights）

Turn on the front lightLower brightness as driving light display.

This function defaults toClose.

1.1.5taillamp

Light orDRLOpenThe taillights are always on when braking, and flash when braking..

1.1.6ScatterHot airfan

ScatterThe cooling fan is used to cool the headlights. By default, the cooling fan will only run automatically when the headlights are turned on, but it can also be turned on byAPPmiddle【Forced air cooling] and [Fan silent mode] to change this default behavior.

1.1.7limitspeed

1. handLimit of dynamic adjustmentspeed

Available inAPPInside HandAutomatically adjust the maximum speed limit of the vehicle, the maximum adjustable speed referenceAPPFunction【Maximum speed limitadjust】

1. Dynamic Limitspeed

The vehicle will intelligently calculate the maximum speed that can be achieved based on the current vehicle status, etc. When the vehicle battery is low or the user is heavy, the vehicle may not be able to reach the manually adjusted limit.speed

1.1.8Speeding warningtell

whenWhen the vehicle speed is about to exceed the dynamic speed limit, the vehicle will be rocked and voice alarm will sound (the alarm content depends on the sound package currently used by the vehicle; the alarm sound volume is fixed at100%）;

1.1.9Lockcar

After locking the vehicle, the vehicle is disabled and cannot maintain front and rear balance. There is resistance when the vehicle is turned on..

1.1.10DefendFlying Spinable

existWhen the vehicle is stationary, hold the switch under the handle to stop the motor and hear the vehicle key tone.APPEnable or disable this feature.

This function defaults toConfirm to open.

1.1.11Cycling ModelMode

support2kindThe riding modes are [Normal Mode] and [Enthusiast Mode]. In [Normal Mode], the maximum speed limit is50km/h，【In the fever mode, the maximum speed limit can reach55km/h, and otherCycling parametersxxx.

1.1.12Drive moduleMode

support2kindThe driving modes are [Comfort Mode] and [Off-road Mode]. In [Comfort Mode],xxxx; In [Off-road Mode],xxx.

1.1.13Pedal sensitivitySpend

Support infinite pedal sensitivityAdjustment range0-100%In addition, supportAdjust the pedal sensitivity in [Comfort Mode] and [Off-road Mode] separately, refer toAPPFunctionPedal sensitivity】Functionillustrate.

1.1.14Forced Windcold

SupportBy setting the cooling fan to always be in working state when the machine is turned on, refer toAPPFunctionForced air cooling] Function description.

1.1.15Fan Silent ModeMode

SupportThe headlights and cooling fans can be set to work more intelligently. For example, when the headlights are turned off, the cooling fans do not work; when the headlights are turned on, the cooling fansOr promotion statusThe fan will automatically turn off in this state, and the maximum brightness of the lights will automatically decrease. When you ride, the fan will automatically turn on, and the brightness of the lights will be restored..

This function is from the human machine boardV1.1.62After support, refer tohere.

1.1.16Backup powerquantity

This feature allowsIn low power conditions, the20%Left and rightYou can continue riding by draining the battery, but the speed and power will be limited to a lower value. You also need to charge as soon as possible to avoid damaging the battery. This function will not be saved when the power is turned off..

This function is from the human machine boardV1.1.62After that, support starts, refer tohere.

This function is already available on the HMI board.V1.2.1afterDelete, refer tohere.

1.1.17LowElectrical safety moduleMode

This mode canWhen the battery is low, the speed limit and other measures are takenTo maximize the protectionProve vehicle safety.WakashiClose this mode, when the battery is lower than50%Do not ride vigorously when riding. High speed, climbing steep slopes or rapid acceleration may cause instability or even fall and injury..

This function is factory default.Confirm to open.

This function is from the human machine boardV1.2.22,Driver boardV4.1.29After that, support starts, refer tohere.

1.1.18Acceleration and decelerationFeed

PassChange the riding feel by adjusting acceleration feedback and deceleration feedback separately.

CanAdjustment range[0, 100],The larger the value, the faster the/The harder the deceleration feels;The smaller the value, the faster the/The deceleration sensationSoft.APPSwitch acceleration and decelerationFeedback function and adjustment of acceleration and deceleration feedback value.

This function is factory default.Close.

This function is from the human machine boardVx.xx,Driver boardVx.xxAfter that, support starts, refer to.

1.1.19nullCarrying inspectionMeasurement

This feature canDetects when the vehicle leaves the ground when unloaded. When this happens, you can hear an unloaded warning tone and the motor will stop working to prevent the unloaded wheels from spinning. It can usually be used to replace the anti-spin button to lift the test.

This function is factory default.Close.

This function is from the human machine boardV1.2.1,Driver boardV4.6.0After that, support starts, refer tohere.

1.1.20Intelligent battery life estimationCalculate

According to the useUser cycling habits (recently3km) Intelligent estimation of the remainingEndurance. You need to ride after first opening.3kmIt can be estimatedrecharge mileage.

This function is factory default.Close.

This function is from the human machine boardV1.2.22,Driver boardV4.1.29After that, support starts, refer tohere.

1.1.21Auxiliary levelBalance

This feature canxxx.

This function is factory default.Close.

This function is from the human machine boardVx.xx,Driver boardVx.xxAfter that, support starts, refer to.

1.1.22transportInput modeMode

Enabling this feature can preventThe vehicle was accidentally started during transportation, causing a safety accident.APPToggle this mode on or off.To release shipping mode, plug in the charger.

Please confirm before mailingAPPTurn on this mode.

This function is factory default.Confirm to open.

1.1.23Vehicle calibrationjust

1. Balance AngleTuneFestival

CanAdjust the vehicle's front and rear balance zero point.

1. Turning forward calibrationjust

whenWhen the vehicle tilts forward when turning, it may be corrected by turning forward correction to improve this phenomenon.

CorrectionMake sure the vehicle is perpendicular to the ground.

1. Motor Adaptationanswer

Motor adaptation can improve the riding experience to a certain extent. Generally, this operation is not necessary unless you have replaced the motor yourself, or your vehicle has numbness, slight shaking, etc. when riding..

ifThe riding effect has not improved after the adaptation. It is recommended to clear the adaptation effect..

1.1.24Restore Factoryset upPlace

AllThe vehicle settings (including sound effects, etc.) are restored to factory default parameters.

1.1.25FaultInspectionMeasurement

Fault sharingFor driver board, communication ,Motors, Batteries and Fans5bigClass, supports up to25Item failure and26WarningsDetection.

The vehicle fault table is as follows.

Faultkindtype	Fault classificationkind	APPdescribe	establishProposed solutioncase	PreparationNote
MutuallyCurrent sensor failurebarrier	driveplate	MutuallyCurrent sensor failurebarrier	You may need toTo replace the driver board, please contact the agent or Lexing salesback
Total current sensor failurebarrier	driveplate	Total current sensor failurebarrier	You may need toTo replace the driver board, please contact the agent or Lexing salesback
Motor Hall Effectbarrier	electricitymachine	Motor Hall Effectbarrier	You may need toTo replace the motor, please contact the agent or Lexing salesback
Battery failure (battery internal error）	electricityPool	Battery failurebarrier	You may need toTo replace the battery, please contact the dealer or Lexing salesback
postureState sensor failurebarrier	driveplate	IMUSensor failurebarrier	You may need toTo replace the driver board, please contact the agent or Lexing salesback
Driver communication failure (the human-machine board cannot receive data from the driver board）	plateIntercommunication	Driver communication failurebarrier	You may need toTo replace the mainboard or driver board, please contact the agent or Lexing salesback
Driver communication failure (driver board cannot receive data from human-machine board）	plateIntercommunication	Driver communication failurebarrier	You may need toTo replace the mainboard or driver board, please contact the agent or Lexing salesback
Bluetooth board communication failure (the human-machine board cannot receive data from the Bluetooth board）	plateIntercommunication	Bluetooth board communication failurebarrier	You may need toTo replace the mainboard or Bluetooth board, please contact the agent or Lexing salesback
Bluetooth board communication failure (Bluetooth board cannot receive data from the human-machine board）	plateIntercommunication	Bluetooth board communication failurebarrier	You may need toTo replace the mainboard or Bluetooth board, please contact the agent or Lexing salesback
MOSTemperature control failure	driveplate	MOSTemperature control failure	You may need toTo replace the driver board, please contact the agent or Lexing salesback
Motor temperature control failurebarrier	electricitymachine	Motor temperature control failurebarrier	You may need toTo replace the motor, please contact the agent or Lexing salesback
Battery temperature control failurebarrier	electricityPool	Battery temperature control failurebarrier	You may need toTo replace the battery, please contact the dealer or Lexing salesback
Temperature control failure in the high temperature area of ​​the mainboard	driveplate	Temperature control failure in high temperature area	You may need toTo replace the driver board, please contact the agent or Lexing salesback
ScatterHeat fan failurebarrier	windfan	ScatterHeat fan failurebarrier	You may need toTo replace the cooling fan, please contact the dealer or Lexing salesback
RTCmoldBlockbarrier	Human Machine Panel	RTCFault	You may need toTo replace the motherboard, please contact the agent or Lexing salesback
External MemoryStoragebarrier	Human Machine Panel	External MemoryStoragebarrier	You may need toTo replace the motherboard, please contact the agent or Lexing salesback
Total voltage sensor failurebarrier	driveplate	Total voltage sensor failurebarrier	You may need toTo replace the driver board, please contact the agent or Lexing salesback
Battery voltage sensor failurebarrier	driveplate	Battery voltage sensor failurebarrier	You may need toTo replace the driver board, please contact the agent or Lexing salesback
Unable to disconnect normallyPower failurebarrier	electricityPool	Unable to disconnect normallyPower failurebarrier	You may need toTo replace the battery, please contact the dealer or Lexing salesback	sinceDriver boardV4.6.xAdded after the version, refer to

The vehicle warning table is as follows.

warnkindtype	APPhint	establishProposed solutioncase	PreparationNote
owePressure on policetell	Low voltage warningtell	Please charge as soon as possible to avoid damaging your battery.Pool
Overvoltage alarmtell	Over voltage warningtell	Please stop usinguse
Overcurrent warningtell
LowElectric bike current overload warningtell
LowElectric current over-alarmtell	Overcurrent alarmtell	Please ride gentlyOK
LowElectrical level1~3	LowElectric Policetell	Please charge as soon as possible
MOStemperatureToo high alerttell	Driver temperature over-alarmtell	Please take a restcarve
Motor temperature over high warningtell	Motor temperature over high warningtell	Please take a restcarve
Battery temperature over-alarmtell	Battery temperature over-alarmtell	Please take a restcarve
Mainboard high temperature zone temperatureToo high alerttell	Driver temperature over-alarmtell	Please take a restcarve
Speeding warning	SpeedingCycling Policetell	Please slow downSpend
VectorVoltage saturation alarmtell	SpeedingCycling Policetell	Please slow downSpend
nullTransfer to policetell	Fly to the policetell	Do not lift the vehicle when it is not stationary.
Motor stall alarmtell	Motor stall alarmtell	Do not park on steep slopes.Long
Too large tilt warningtell	Dumping Policetell	Please ride carefullyOK
DangerDangerous riding action warningtell	DangerDangerous riding action warningtell	Don't ride too aggressivelyOK
Motor no-load protection alarmtell	Motor no-load protection alarmtell	establishIt is recommended to open the handle button and make sure the vehicle is still before lifting it.end
There is a necessaryInspection items not conducted or not passedtell	There is a necessaryInspection items not conducted or not passedtell	Please follow the instructions to perform the relevant self-tests before usinguse
eachComponent software mismatch warningtell	eachComponent software incompatibility warningtell	Please upgrade to the latest firmwareItem
The power button is pressed for a long time.tell	Long press the power buttontell	If the power button is pressed for a long time, it may trigger a forced power off. Please stop riding.OK
Forced firmware upgrade warningtell	YourThe vehicle function is limited and needs to be upgraded to work properly.use	Please upgrade to the latest firmwareItem
The vehicle has been lockedtell	YourThe vehicle has been locked. Please contact InMotion after-sales service to verify your identity and unlock it.	Contact Inmotor after-sales service to verify your identity before unlocking
CPUtemperatureToo high alerttell	CPUtemperatureToo high alerttell	Please take a restcarve	Self-manual boardV1.2.1&Driver boardV3.6.1Supported by later versions, refer to
IMUtemperatureToo high alerttell	IMUtemperatureToo high alerttell	Please take a restcarve
eachComponent hardware mismatch warningtell	eachComponent hardware mismatch warningtell	Motherboard andThe driver board needs to be replaced as a whole set. Disassembly and reassembly are prohibited.
Fan speed too low warning (will force the maximum brightness of the headlight to be reduced）	ScatterThermal fan speed too low alarmtell	This will affect the maximum brightness of the light. Please check if there is any foreign object blocking the fan.Plug
SomeBattery dead alarmtell	SomeBattery dead alarmtell	This will affect the performance of the vehicle, please use with caution.use
Battery voltage calibration abnormal alarmtell	Battery voltage calibration abnormal alarmtell	Please recalibrate the battery voltage

1.1.26soundeffect

SupportChange the voice package and support replacing a single voice (give priority to playing a single voice).DIYofA single sound effect does not affect the current voice package and can be deleted independently.

1.1.27Cycling Notesrecord

supportRecord every ride of the vehicle.3kmandDuration exceeds1minWhen the vehicle is turned off, it will save the riding record. The riding record data includes the mileage, maximum speed, average speed, maximum power, energy consumption, duration, etc..

This function is from the human machine boardV1.1.62&Driver boardV3.4.8After support, refer tohere.

1.1.28Firmware Updatenew

In-car human-machine interaction board, driver board, BluetoothBoard supportsOTAUpdate. Available atAPPInsideDetecting firmware updates and completing updates.

1.1.29 RTCClockstep

supportSet up the panelRTCClock Time.

In general, each timePassAPPAutomatically synchronize the phone system time to the car when connected to the carRTCclock.

1.1.30Voice promptShow

In operationWhen the vehicle or vehicle detects an abnormality, there will be a corresponding voice prompt.APPCustomize sound effects, turn them on and off, adjust the volume, etc..

1.2Other functionsable

1.2.1Chargeelectricity

Use original chargerElectrical appliances (output voltage is84VDC/2.5A)ChargeWhen charging, the charger light turns red to indicate charging; when it turns green, it is fully charged..

Support dual chargingCharging electrical appliances simultaneously can shorten the charging time.

1.2.2pushRod

according toPress the push rod switch under the push rod handle to unlock and unfold the push rod; when the push rod is not in use, hold the push rod switch under the push rod handle to fold it.

1.2.3reduceshock

Dual gasSpring shock absorber.

Be sure to fill the gas spring with gas before use.useStandard pump, compared with [weight-gasPressure gauge, use after filling the gas spring, the air hole is at the bottom of the pedal.

1.2.4stopCarshelf

downTurn the parking bracket to park.

2 APPachievementable

2.1Stimulatelive

When connecting a new, inactive vehicle,APPWillThe system will automatically jump to the activation page. After activation, you can authenticate the owner according to the page prompts..

2.2Lock the car/untieLock

SolvableLock/Locked vehicle.

Need toAPPInsideThe car can be locked only after the owner is authenticated/untieLock.

2.3Light onclose

Switchable front lights.

2.4Light onSpend

CanAdjust the brightness of the front lights.

2.5 DRL(OKHeadlights）

SwitchableDRL.

2.6DefendFlying Spinable

Switchable protectionFlying function. After turning it off, the anti-flying button will not work.

2.7Maximum speed limitTuneFestival

whenWhen the vehicle's riding speed reaches the set maximum speed, a voice alarm will sound (the alarm content depends on the sound effect package currently used by the vehicle; the alarm sound volume is100%)andSeesaw;

Available inAPPInsideAdjust this maximum speed limit. For specific alarm speed limits, refer to the maximum speed column in the main parameter table of each vehicle model.;

2.8Limit the maximum speed to25km/h

25km/hThis is the safety speed recommended by the manufacturer. After turning on this switch, the maximum adjustable speed will be limited to25km/h;closeAfter turning off this switch, the maximum speed can be adjusted to the maximum speed supported.;

2.9Cycling ModelMode

CuttableChange the current riding mode to [Normal Mode] or [Fever Mode].

This function defaults toTo confirm hidden, click the setting page title continuously5Only aftershow(If the currentIf the vehicle is already in enthusiast mode, this function will be displayed without the above operation).

2.10Drive moduleMode

CuttableSwitch the current driving mode between [Normal Mode] and [Off-road Mode]. When switching driving modes, the pedal sensitivity adjustment slider will also be updated to the value in the corresponding driving mode..

2.11Pedal sensitivitySpend

CanAdjust the current drive modeDownThe corresponding pedal sensitivity value. Adjustable range[0-100%].

2.12Forced Windcold

2.13Fan Silent ModeMode

2.14soundquantity

CanAdjust the volume and range of the vehicle voice package[0-100%].

Note: PartThe volume of alarm sound effects such as overspeed alarm and fault alarm is fixed at100%, cannotadjust.

2.15Backup powerquantity

2.16LowElectrical safety moduleMode

Switchable lowElectrical safety mode switch.

2.17Somatosensory separation mode/Acceleration and decelerationFeed-offclose

Can switch acceleration and decelerationFeedback switch.

2.18AccelerationFeedbackFestival

CanAdjust the acceleration feedback strength, adjustable range[0-100%].

Note:Adjustable only when the acceleration/deceleration feedback switch is turned on.

2.19DecelerationFeedbackFestival

CanAdjust the deceleration feedback strength, adjustable range[0-100%].

Note:Adjustable only when the acceleration/deceleration feedback switch is turned on.

2.20nullCarrying inspectionMeasurement

SwitchableLoad detection switch.

2.21Intelligent battery life estimationCalculate

SwitchableEndurance intelligent fault switch.APPhostPage to view remaining mileage.

2.22Auxiliary levelBalance

SwitchableAuxiliary balance switch.

2.23transportInput modeMode

SwitchableInput Mode.

2.24Vehicle calibrationjust

2.24.1Balance AngleTuneFestival

CanAdjust the front and rear balance angle of the vehicle. Adjustable range [-10~10°】, scale0.1°.

2.24.2Turning forward calibrationjust

CanCorrection of forward lean during turning.

2.24.3Motor Adaptationanswer

CanPerform motor adaptation and clear motor adaptation results.

2.25Restore Factoryset upPlace

CanRestore the vehicle to factory settings.

Note: This function requiresCarry out when the vehicle is disabled.

2.26FaultInspectionMeasurement

CanDetect vehicle faults and warnings.

whenThe test results include“Battery voltage calibration abnormal warning”When the battery voltage is calibrated, you can follow the prompts on the page.;

whenThe test results include“There is a necessaryWarning for inspection items not conducted or not passed”You can perform self-check on the page according to the prompts;

2.27soundeffect

CuttableChange the current sound pack andDIYSingle sound effect.

2.29aboutcarVehicle

2.29.1baseFoundationinterest

CanView the basic vehicle information, including the followingAllow

• vehicleSN
• Activation DayExpect
• Human-computer interaction board,Bluetooth board and driver board versionNumber
• TotalProcedure
• MOS,Driver board,CPUandIMUtemperatureSpend
• Remainingelectricityquantity
• electricityPressure
• ChargeElectricPressure

2.29.2Battery letterinterest

Vehicle presence2indivualBattery, you can view detailed information about each battery, including the followingAllow

• electricityPressure
• Is it effective?/Invalid, indicating whetherThe battery is detected）
• Is it enabled?/Not enabled, meaningIs the battery in working condition?）
• Is it a fault (normal/Fault/SignalLogical exceptions）